|
MATERIAL SAFETY DATA SHEET
Distributed
By:
PHONE: 303-373-4860
Scott’s Liquid
Gold-Inc.
MSDS DATE: 03-02-06
4880 Havana
Street
REPLACES: 10-23-01
IDENTIFICATION
PRODUCT NAME:
Mold Control 500 Part A
COMPOSITION:
Mixture of cationic detergents and fatty alcohols
_ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _
ACTIVE
INGREDIENTS: % OSHA
PEL ACGIH
Qauternary
Ammonium Compounds,
Benzyl-C12-18
Alkyl Dimethyl
3.2 Not Established
(CAS 68391-01-5)
INERT
INGREDIENTS
96.8
TOTAL
100.00
______________________________________________________________________________________
PHYSICAL DATA
APPEARANCE:
clear straw liquid SOLUBILITY IN WATER:
Complete
ODOR:
Sweet SPECIFIC
GAVITY: 0.99
EVAPORATION
RATE: 1
(water=1) pH of CONCENTRATE: 9.3
VAPOR PRESSURE:
Unknown BOILING POINT: 212OF.
FIRE AND EXPLOSION DATA
FLAMMABILITY:
Not flammable
EXTINGUISHING
MEDIA: Water, Carbon Dioxide, Foam
UNUSUAL FIRE
AND
EXPLOSION
HAZARDS: NONE KNOWN
HEALTH HAZARD DATA
EYE EFFECT:
Contact with eyes may cause severe irritation; prolonged eye contact
may cause permanent damage.
SKIN EFFECT:
Prolonged contact with eyes may cause irritation or burns.
INGESTION:
If swallowed, consult a physician can cause severe damage to
mucous membranes.
INHALATION:
No effect known.
CARCINOGENICTY:
This product (or components of its mixture) is not listed in IARC
Monographs, the NTP Sixth Annual Report or the current ACGIH TLV’s as
a carcinogen or potential carcinogen.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT:
Flush eye with cool running water for at least 15 minutes. If redness
or irritation develops get medical attention.
SKIN CONTACT:
Flush with cool running water or wash with soap and water. If
irritation develops get medical attention.
INGESTION:
If conscious, induce vomiting give several glasses of water or milk.
Get medical attention.
BREATHING:
Move to fresh air. If breathing becomes heavy seek medical attention
Mold Control 500 Part A Page 2
SPECIAL PROTECTION
INFORMATION
PROTECTIVE
GLOVES: Recommended (rubber or PVC),
EYE PROTECTION:
Recommended (goggles, safety glasses), they should always be worn
LOCAL EXHAUST:
Recommended
OTHER
EQUIPMENT: Not required
REACTIVITY DATA
INCOMPATIBLE
MATERIALS: Strong Oxidizers,
Anionic materials
STABILITY:
Product is stable
POLYMERIZATION:
Will not occur
DECOMPOSITION
PRODUCTS: May give off
nitrous oxides and ammoniacal vapors during a fire.
SPILL OR LEAK PROCEDURES
SPILL:
Contain all spills and leaks to prevent discharge into the
environment.
Soak up with an absorbent, shovel into waste
containers, flush with water.
DISPOSAL:
Remove material or dispose of (incineration is preferred) in
accordance with all
applicable federal, state and local regulations.
Material collected with absorbent
may be disposed of in a permitted landfill in
accordance with federal, state and
local regulations.
ADDITIONAL INFORMATION
SARA requires
submission of annual reports of release of toxic chemicals that appear
in 40 CFR 372. This Information must be included in all MSDS’s that
are copied and distributed for this material.
Components present
in this product at a level, which could require reporting under the
statute: NONE
MATERIAL SAFETY DATA SHEET
Distributed By:
Scott’s Liquid
Gold-Inc.
PHONE: 303-373-4860
4880 Havana
Street
MSDS DATE: 03-02-06
Denver, CO
80239
REPLACES: 6-10-98
IDENTIFICATION
PRODUCT NAME:
Mold Control 500 Part B
COMPOSITION:
Hydrogen peroxide, water and inert
ingredients.
HAZARDOUS
INGREDIENTS: % TLV
LIMIT IN AIR
Hydrogen Peroxide
(7722-84-1) 7.99 1
ppm
Inert
Ingredients
92 N/A
Total
100
PHYSICAL DATA
APPEARANCE:
Colorless
liquid ODOR: Odorless
SOLUBILITY:
Soluble BOILING
POINT: 108O C (226O F)
MELTING POINT:
-33 VAPOR DENSITY:
Not Available
VAPOR PRESSURE:
23.3 MM HG @ 30o C SPECIFIC GRAVITY: 1.1
g/cm (H2O=1)
EVAPORATION RATE:
above 1
FIRE AND EXPLOSION DATA
FLASH
POINT: Non-Flammable
EXPLOSION:
Not considered an explosion hazard.
FIRE
EXTINGUISHING MEDIA: Water.
Evacuate enclosed and surrounding areas. If smoke and fumes. Cannot be
avoided, use proximity suit and self-
contained
breathing apparatus. Use water spray to cool. containers and disperse
vapors. Keep spill away from sources of ignition.
SPECIAL
INFORMATION: Heating may cause explosion.
HEALTH HAZARD DATA
v
Vapor irritating to the
eyes and respiratory tract.
v
Do not get in eyes, on
skin, or on clothing.
v
Avoid breathing mist.
v
Wash thoroughly after
handling.
v
Store in tightly closed
container.
v
Combustible Liquid Vapor.
EMERGENCY AND FIRST AID PROCEDURES
INHALATION:
If inhaled
remove to fresh air. Give oxygen if breathing is difficult. If
breathing has stopped, give artificial respiration. Call a physician
immediately.
INGESTION:
If
swallowed, do not induce vomiting. Give victim a glass of water. Call
a physician immediately. Never give anything by mouth to an
unconscious person.
SKIN
CONTACT: In case
of contact, flush skin with plenty of water for at least 15 minutes
while removing contaminating clothing. Call a physician immediately.
EYE CONTACT: In
case of contact, immediately flush under upper and lower eye lids with
plenty of water for at least 15 minutes. Call a physician immediately.
CHRONIC
EXPOSURE: No chronic effects are known for humans.
PAGE
2 MOLD CONTROL 500 Part B
SPECIAL PROTECTION INFORMATION
RESPIRATORY
PROTECTION: Atmospheric levels should be maintained
below the exposure limits. Listed in
Section III by using engineering controls. If not feasible, Use
approved full face-piece air-purifying respirator.
VENTILATION
Provide general and/or
local exhaust ventilation to SYSTEM: maintain airborne levels
below the exposure limits in Section III. Refer To “Industrial
Ventilation” ACGIH for a manual of recommended practices.
SKIN
PROTECTION: If skin or contamination of clothing is likely,
protective clothing should be worn.
EYE
PROTECTION: Chemical
goggles are required.
PROTECTIVE
GLOVES:
Wear chemical resistant gloves.
REACTIVE DATA
STABILITY:
Stable at normal temperatures and
condition of storage.
HAZARDOUS
DECOMPOSITION
PRODUCTS:
Oxygen which supports combustion.
HAZARDOUS
POLYMERIZATION:
Will not undergo hazardous
polymerization.
INCOMPATIBILITIES:
Heavy metal ions, alkalis, and
combustible materials.
SPILL
OR LEAK PROCEDURES
SPILL: See
Section V and IV for hazards and exposure controls. Dike with sand or
Earth to contain spill. Avoid ignition sources. Absorb with sand to
other non-Flammable material and transfer to approve DOT drum for
recovery or disposal.
DISPOSE: Dispose of
in accordance with all local, state and federal regulations.
GENERAL:
CERCLA/SARA requires
notification to the appropriate Federal state and local Authorities of
releases of hazardous or extremely hazardous quantities equal to Or
greater than the Reportable Quantities (RQs) in 50 CFR 302.4 and 40
CFR 355. SARA Title 313 requires submissions of annual reports of
releases of toxic Chemicals that appear in 40 CFR 372. Components
present in this product at a Level which could require reporting under
statute is listed in Section XII.
MATERIAL SAFETY DATA SHEET
DISTRIBUTED BY:
Scott’s Liquid
Gold-Inc
PHONE: 303-373-4860
4880 Havana
St.
MSDS DATE: 03-02-06
Denver, CO
80239
REPLACES: 09-15-00
IDENTIFICATION
PRODUCT
NAME: Mold Control 500
Mixture Part A & B
COMPOSITION:
Mixture of cationic detergents and peroxide
ACTIVE
INGREDIENTS:
% OSHA PEL ACGIH
N,N,N,N1,N1-Pentamethyl,N1-Tallow
Alkyl 1,3-Propanamine 0.5 Not Established
Diammonium
Chloride; n-Tallow Pentamethyl Propane (CAS 68607-29-4)
Quaternary
Ammonium Compounds, Benzyl-C12-18 Alkyl Dimethyl 1.6 Not
Established (CAS 68391-01-5)
Isopropyl Alcohol
(CAS
67-63-0)
0.5 400PPM
Hydrogen Peroxide
(CAS 007722-84-1)
4.0 1.4mg/m3
INERT
INGREDIENTS
93.4
TOTAL
100.00
PHYSICAL DATA
APPEARANCE:
clear
liquid SOLUBILITY IN WATER:
Complete
ODOR:
Sweet
SPECIFIC GRAVITY: 1.01
EVAPORATION
RATE: 1 (water=1) pH of CONCENTRATE: 9.7-9.8
VAPOR PRESSURE:
Unknown BOILING POINT: 212O
F.
FIRE AND EXPLOSION DATA
FLAMMABLITY:
Not flammable
EXTINGUISHING
MEDIA: Water, Carbon Dioxide, Foam
UNUSUAL FIRE
AND
EXPLOSION
HAZARDS: NONE KNOWN
HEALTH HAZARD DATA
EYE EFFECT:
Contact with eyes may cause
sever irritation, prolonged eye contact may cause permanent damage.
SKIN EFFECT:
Prolonged contact with eyes
may cause irritation or burns.
INGESTION:
If swallowed, consult a physician can cause severe damage to mucous
membranes.
INHALATION:
No effect known.
CARCINOGENICITY: This product (or components of its mixture) is not listed in IARC
Monographs, the NTP Sixth Annual Report
or the current ACGIH LTV’s as a carcinogen or potential carcinogen.
EMERGENCY & FIRST AID PROCEDURES
EYE CONTACT:
Flush eye with cool running
water for at least 15 minutes lifting eyelids occasionally. Get
medical attention if redness or irritation develops.
SKIN CONTACT:
Flush with cool running
water. If irritation develops get medical attention.
Mold
Control 500 Part A & Part B Page 2
INGESTION:
If conscious, give several
glasses of water or milk. Get medical attention immediately.
BREATHING:
Move to fresh air. If
breathing becomes heavy seek medical attention.
SPECIAL PROTECTION INFORMATION
PROTECTIVE
GLOVES: Recommended (rubber or PVC)
EYE PROTECTION:
Recommended (goggles, safety glasses of face shield)
LOCAL EXHAUST:
Recommended when used in a
confined space
OTHER
EQUIPMENT: None required
REACTIVITY DATA
INCOMPATIBLE
MATERIALS: Strong
Oxidizers, Anionic materials
STABILITY: Product
is stable
POLYMERIZATION: Will
not occur
DECOMPOSITION
PRODUCTS: May give off
nitrous oxides and ammoniacal vapors during a fire.
SPILL OR LEAKS PROCEDURES
SPILL:
Contain all spills and leaks to
prevent discharge into the environment. Soak up with absorbent, shovel
into waste containers, flush with water.
DISPOSAL:
Remove material or dispose
of (incineration is preferred) in accordance with all applicable
federal, state and local regulations. Material collected with
absorbent may be disposed of in a permitted landfill in accordance
with federal, state and local regulations When disposing of the used
material after deployment it is acceptable to flush this Maternal down
the drain. This material is active for a period of 8 hours when
flushing it to the drain it is recommended to allow the material to
fully decompose or excessive foaming in the sewer may result.
ADDITIONAL INFORMATION
SARA requires
submission of annual reports of release of toxic chemicals that appear
in 40 CFR 372. This Information must be included in all MSDS’s that
are copied and distributed for this material. Components present in
this product act a level, which could require under the statue, are:
NONE.
MSDS Mold
Control 500
Material Safety Data Sheet
Distributed
By:
Scott’s Liquid
Gold-Inc
PHONE: 303-373-4860
4880 Havana
Street
MSDS DATE: 03-02-06
Denver, CO.
80239
REPLACES: 10-23-01
IDENTIFICATION
PRODUCT
NAME: Mold Control 500 Propellant Cartridge
CHEMICAL PRODUCT AND COMPANY
IDENTIFICATION
Material
Identification
CAS:
Number: 75-37-6 100
CAS:
Name: ETHANE, 1, 1-DIFLUORO
Formula: CH3CHF2
Company MSDS
Number: TECHVN988
Company
Identification: Techven (USA) LLC
16 Bayside
Irvine, CA
92614-7987
Phone Numbers
Product
Information: 1-949-653-8936
Transport
Emergency: 1-800-424-9300 (CHEMTREC)
Medical
Emergency 1-800-424-9300 (CHEMTREC)
COMPOSITION AND INFORMATION OF
INGREDIENTS
Ingredients
Ingredient
Sequence Number: 01
Ingredient
Name: Ethane, 1, 1-Difluoro-(HFC – 152a)
CAS
Number: 75-37-6
Percentage: 100%
HEALTH HAZARDS
Potential
Health Effects
Inhalation of
HFC-152a concentration of vapor is harmful and may cause nonspecific
discomfort such as nausea, headache or weakness, or temporary nervous
system depression with dizziness, confusion, in coordination,
drowsiness or unconsciousness. Contact with the liquid may cause
frostbite. Higher exposure may lead to irritation of nose, throat, and
lungs with cough, difficulty breathing or shortness of breath,
temporary alteration of the heart or electrical activity with
irregular pulse, palpitations, or inadequate circulation, or abnormal
kidney function as detected by laboratory tests. Gross overexposure
may be fatal. Vapor reduces oxygen available for breathing and is
heavier than air.
Carcinogenicity
Information None of the components present in this material at
concentrations equal to or greater than 0.1% is listed by IARC, NTP,
OSHA or ACGIH as a carcinogen.
MSDS Mold
Control 500
FIRST AID
INHALATION
If high
concentrations are inhaled, immediately remove to fresh air. Keep
person calm. If not breathing, give artificial respiration. If
breathing is difficult, give oxygen. Call a physician.
SKIN CONTACT
In case of
contact, immediately flush skin with plenty of water for at least 15
minutes. Treat for frostbite necessary, by gently warming affected
area.
EYE CONTACT
In case of
contact, immediately flush eyes with plenty of water for at least 15
minutes. Call a physician.
INGESTION
Not considered as
a likely exposure.
PHYSICAL AND CHEMICAL PROPERTIES
Boiling
Point: -25 C (-13 F)
Vapor
Pressure: 87 psia at 25 deg C (77 deg F)
Vapor
Density: 2.4 (Air = 1.0) at 25 deg C (77 deg
F)
%
Volatiles: 100 WT%
Solubility in
Water: 0.28 WT% @ 25 C (77F) (87 psia)
Odor:
Slightly ethereal
Form: Gas
Color: Clear, colorless
Density: 0.90 g/cc at 25 deg C (77
deg F) – Liquid
CHEMICAL
STABILITY AND REACTIVITY
Chemical
Stability
Material is
stable. However, avoid open flames and high temperatures.
Incompatibility
with Other Materials
Incompatible
with alkali or alkaline earth metals- powdered Al, Zn, Be, etc.
Polymerization
Polymerization
will not occur.
Decomposition:
Decomposition
products are hazardous. This material can be decomposed by high
temperatures (open flames, glowing metal surfaces, etc.) forming
hydrofluoric acid and possibly carbonyl fluoride.
MSDS Mold
Control 500
FIRE HAZARDS
Flammable
Properties
Flash
Point: <-50 C (<-158 F)
Flammable
limits in Air % by Volume
LEL:
3.9
UEL:
16.9
Autoignition:
454 C (849 F)
Fire and
Explosion Hazards:
Flammable.
Cylinders are equipped with temperature and pressure relief devices
but may still rupture under fire conditions.
Extinguishing
Media
Water Spray,
Water Fog, Dry chemical, Carbon dioxide. (CO2) “Alcohol” foam.
Fire Fighting
Instructions
Keep container
cool with water spray. If gas exiting container ignites, stop flow of
gas. Do not put out the fire unless leak can be stopped immediately.
Self-contained breathing apparatus (SCBA) is required if containers
rupture and contents are released under fire conditions.
HANDLING AND STORAGE
Handling
(Personnel)
Avoid breathing
high concentrations of vapors and avoid liquid contact with skin or
eyes. Use with sufficient ventilation to keep employee exposure below
recommended limits. Lines and equipment which will contain HFC-152a,
Aerosol Propellant should be pre-tested with nitrogen using soapy
water to detect leaks.
Storage
Clean, dry
area. Do not heat above 52 deg C (125 deg F).
EXPOSURE CONTROL AND PERSONAL
PROTECTION
Engineering
Controls
Normal
ventilation for standard manufacturing procedures is generally
adequate. Local exhaust should be used when large amounts are
released. Mechanical exhaust should be used in low or enclosed places.
Ground all equipment and cylinders before use. Use explosion-proof
electrical equipment rated Class I, Group D in Division I locations.
In Division 2 locations, all spark-producing electrical equipment must
be explosion-proof and rated Class I, Group D.
Personal
Protective Equipment
Impervious
gloves and chemical splash goggles should be worn when handling the
liquid. Fire protective clothing (NOMEX) with antistatic control
should be worn handling this product. Under normal manufacturing
conditions, no respiratory protection is required when using this
product. Self-contained breathing apparatus (SCBA) is required if a
large release occurs.
Exposure
Guidelines
Exposure Limits
152a AEROSOL PROPELLANT
Page 3 of 6
MSDS Mold Control 500
PEL (OSHA):
None Established
TLV (ACGIH):
None Established
WEEL (AIHA):
1000 ppm, 8 Hr. TWA
ACCIDENTAL RELEASE
Safeguard
(Personnel)
Review “FIRE
HAZARDS” and “HANDLING AND STORAGE” and “EXPOSURE CONTROL AND PERSONAL
PROTECTION” section before proceeding with clean-up. Use appropriate
PERSONAL PROTECTIVE EQUIPMENT during clean-up.
Accidental
Release Measures
If a spill can
cause a concentration in excess of 1, 000 ppm, of HFC – 152a, turn off
valves and ignition sources, Evacuate area, Ventilate area, especially
low places where heavy vapors might collect. Wear self-contained
breathing apparatus (SCBA).
If this product
is spilled and not recovered, or is recovered as a waste for treatment
or disposal, the CERCLA Reportable Quantity is 100 lbs. (Released of
an unlisted Hazardous Waste characteristic of ignitability).
TOXICOLOGY DATA
Animal Data
Oral ALD:
>1500 mg/kg in rats
Inhalation ALC,
4 hr: 383, 000 ppm in rats
This material
demonstrates for skin and eye irritability, and for animal
sensitization.
Test in animal
demonstrate no carcinogenic activity or development effects.
Tests in
animals for reproductive effects have not been performed. This
material does not produce genetic damage in bacterial cell cultures,
but has not been tested in animals.
Effects in
animals for single, high exposure by inhalation labored breathing,
lung irritation, and lethargy, lack of coordination and loss of
consciousness. Effects of repeated exposure include increased urinary
fluorides, reduced kidney weight, and reversible kidney changes.
The effects of
a single, high oral dose include weight loss and lethargy.
DISPOSAL
Waste Disposal
Reclaim by
distillation, incinerate, or remove to a permitted waste facility.
Comply with Federal, State, and local regulations.
This material
may be a RCRA Hazardous waste upon disposal due to the ignitability
characteristic.
TRANSPORTATION DATA
Shipping
Information:
DOT/IMO
Page
4 of 6
MSDS Mold Control 500
Proper Shipping
Name: 1, 1-DIFLUOTOETHANE
Hazard
Class: 2.1
UN
No: UN 1030
Label:
FLAMMABLE GAS
Special
Information: CARGO AIRCRAFT ONLY
IMO Regulations
Page No. 2132 (1997)
PSN Code
DOT FBB
IMO FTF
IATA
JLT
AFI
JLT
Shipping
Containers
Cylinders
Ton Tanks
Isocontainers (Isotanks)
REGULATORY INFORMATION
U.S. Federal
Regulations
TSCA Inventory
Status: Reported/Included.
TITLE III
HAZARD CLASSIFICATIONS SECTIONS 311, 312
Acute: Yes
Chronic: No
Fire: Yes
Reactivity: No
Pressure: Yes
Listed under
SARA Extremely Hazardous Substance - No
CERCLA Hazardous Substance - See
“DISPOSAL”
SARA Toxic Chemicals - No
OSHA in 29CRF
1910.1200(c); defined hdc-152a is a flammable gas. Use of this product
may require compliance with 29CFR 1910.119, Process Safety Management
of Highly Hazardous Chemicals.
OTHER INFORMATION
NFPA, NPCA-HMIS
NPCA-HMIS
Rating
Health: 1
Flammability: 4
Reactivity: 1
Personal
Protection rating to be supplied by users depending on use
Page 5 of 6 |
